How to apply VIS INFLUERE®
VIS INFLUERE® is a high frequency device of the latest design. VIS INFLUERE® generates high-frequency currents, i.e. electrical alternating currents with very high frequencies (around 1 to 2 million per second). The whole device unit consists of a control unit with LED display for amplitude and impulse, the VIS INFLUERE® rod containing a hand-blown glass tip with a quartz crystal and argon gas. This glass tip is also referred to as an electrode which generates ultraviolet radiation around the specially ground pure crystal. As opposed to other high frequency devices, the VIS INFLUERE® has been developed as an ‘all-in-one’ device. VIS INFLUERE® is characterised specially by its mobility.
The vasodilator effect of the high frequency stimulates the whole human organism and optimises the function of the organs; i.e. there is a better blood circulation and an increase in the oxygen content of the blood and tissue. The VIS INFLUERE® - high frequency creates an acceleration of the metabolism, has a bactericidal and germicidal effect and releases ozone as a result of weak, harmless spark discharges. The application areas of the VIS INFLUERE® - high frequency are practically unlimited, apart from the fact that the VIS INFLUERE® - high frequency can only be used for non-invasive applications.
The values stated are for average people. Case-by-case, a person's individual sensitivities vary. Start the ball rolling with average values and together with the client/patient find the best setting for that person.
It is however advisable to start with average settings of minus 1.0 to 2.0 for amplitude, and minus 10 to 20 for impulse, for children and sensitive people. LED displays show the exact numbers.
A higher and lower setting can always be made in step with amplitude and impulse. Any increase should however only be carried out in agreement with the Client/Patient, since the effect is only improved if the Client/Patient feels good. The setting is then written on the respective Client/Patient data sheet so the procedure can be continued with the correct setting during a follow-up treatment.
Less is sometimes also more. Note however that even if desired treatment success occurs earlier than the stated duration of treatment, this should nevertheless be adhered to so as to ensure sustainability.
It is vital that the crackling sound of the VIS INFLUERE® rod be explained to the Client/Patient, since they will get an ancillary effect along with the intended treatment. This small, harmless spark discharge releases pure ozone. In addition to accelerating the metabolism, it also yields a bactericidal and germicidal (bacteria) effect. This pure ozone penetrates the skin and cleanses the blood.
The glass tip is positioned directly on the part of the body which is to be treated. The tip is gently, without exerting a great deal of pressure, administered all around the area to be treated. After this continue on the trigger points pausing for a max. of 20 seconds on the same site. It is also advisable to carry out the treatment with the tip and with the tip positioned at an angle too.
Direct treatment is also possible, if the skin is not directly touched. I.e. It also works when there is material between the skin and the tip.
This triggers a gentle or a stronger prickling, depending on the setting. This prickling is wholly benign and if anything releases pure ozone which penetrates through the pores in the skin and cleanses it.
Start by activating the meridians and lymph channels (energy channels) on the Client / Patients whole body. Place the the tip of the VIS INFLUERE® lightly on the skin and move the rod at an even tempo. Starting with the soles of the feet is recommended, then proceed upwards with the treatment, to the neck and up to the cervical vertebra (Atlas) on the back.
Treat the soles of the feet as they would be during a foot reflex zone treatment, by keeping light pressure on the organ points for around 3 seconds. In doing so you activate individual organs via the meridians and lymphatic pathways. It may well be the case that the Client / Patient will feel this treatment on their organs.
Note:
Meridians are energy conductors and these are not from one single strand. Meridians have several conductive strands and these in turn have several end points. In comparison to acupuncture which uses needles, where an end point, or a strand, is touched with a needle, the VIS INFLUERE® impulse activates all the strands at the same time and links these parallel with other meridians (bridging and also network formation). Meridian activation ends with a somewhat more intense treatment of the spine, right through to the coccyx.
Note:
treatment with VIS INFLUERE® triggers positive auxiliary diathermia.
(Source Wikipedia):
Diathermia (Greek for heat penetration, or diathermy) is an electrotherapy method of physical therapy within medicine, whereby heat is generated in the body's tissues using a high frequency electrical current. Diathermia generates warmth deep down, in contrast to the application of the infra-red waves used in red light therapy, which mainly heat the surface of the skin. During diathermia either electrodes are placed on the skin, and these are linked to a high frequency source, or the ski area affected is radiated via an antenna, which is linked to a generator. In this case a proportion also reaches deep down and can induce eddy currents in the tissues which lead to heat generation. The choice of frequency and the imaginary part of the relative permittivity of the tissue determines to what extent in depth heat generation occurs.
Diathermia may cause a slight reddening of the skin. This is totally harmless and in most cases lasts for no longer than two hours. After treatment we recommend rubbing the reddened areas of skin with arnica oil, which is in the VIS INFLUERE® bag. You may also use oils from your preferred manufacturer. Please pay attention to quality and choose gentle, calming oils.
In general
before you use the Device the first time, read the Technical Manual first.
